Foredom C.FCH-2 User Manual download pdf

QtyDescriptionPart No.Item

CoverCP10852B

Trigger Switch, 250VCP11027

Base

CP10851

Front Base Pad

CP10859

Screw, 6−32 x 1"CP10856

Washer, #6

CP10862

Rear Base Pad

CP10860

Male Cordset or Substitute OptionCP10541

Strain ReliefCP10003−3

Female Cordset (FCT−2)

Female Cordset (FCH−2)

CP10542

CP10868

Wire ConnectorCP11029

Description

Part No.

CPOption20 CP10545 No Plug, Europe

CPOption21 CP10553 Male, United Kingdom

CPOption22 CP10554 Male, Continental Europe

CPOption25 CP10555 Male India 10A

CPOption26 CP10556 Male, Austrailia

Cordset Option

Parts List

C.FCH−2* & C.FCT−2

Foot Control, 230V

FOREDOM The Foredom Electric Company

16 Stony Hill Rd., Bethel, CT 06801 • 203−792−8622

Fax: 203−796−7861

• www.foredom.net

}

Wiring Diagram

*C.FCH−2 is required for use with the latest

SR 230V motors produced since May 2006.

Form DN 12/10

Male Plug to

AC Power Source

Female Receptacle

to Motor

Wire

Connector

Wire Connector

Trigger Switch

BLK (BRN)

GRN/YLW

GRN

BRN (BLK)

BLU (WHT)

WHT (BLU)

GRN

(GRN/YLW)

Most Foot Controls have BLU(WHT) wires connected by a Wire Connector

as shown. Leave them connected, and connect only the BRN((BLK)

wires to Terminals 1 and 6 on the new Trigger Switch. Otherwise

connect all four wires to the Switch as indicated by the dotted wires.

Instructions for Removing

and Replacing Trigger Switch

Using flat blade of screwdriver inserted at Point A

between Cover (1) and Base (3), carefully pry Cover off.

Disconnect Foot Control from Motor and Wall Outlet.

Unscrew cover adjustment screw (5).

On older Switches, all the terminals will be push-in, spring clamp

type. On newer Switches, some terminals have screw fasteners.

To remove wires from the push-in terminals, insert 1.3mm [.05in]

approximate diameter pin or the blade of a jeweler's screwdriver

all the way into the terminal socket to release the spring clamp.

Grasp the tool and wire and pull them together out of the socket.

If you have difficulty removing the wires from the push-in terminals

and you have wire-cutting, stripping, and soldering tools, you can

cut the wires off where they exit from the terminals. To prepare

the cut wires for installation into the replacement Switch, strip

them back exactly 8.25 mm [5/16 in], then apply solder to the

stripped ends to fuse the strands together.

Remove Trigger Switch (2) from Base mounting bracket.

Connect Wires to New Trigger Switch as shown in the Wiring

Diagram. Push wires all the way in, so no bare wire is exposed.

On Screw Terminal 1, push wire lead all the way into the socket

then tighten the screw firmly. Push other wire leads all the way

into the designated terminals. Pull on all the wires, making sure

they are secure. Place Switch back into Base mounting bracket.

Snap cover (1) onto hinge posts on top of rear corners of base (3).

Insert adjustment screw (5) through washer (6) and into post

slot and threaded insert in cover (1). Tighten with screwdriver

until cover is just touching the trigger switch pushrod.

Do not

tighten the screw further

to avoid pressing the Switch Pushrod

into a permanently "on" position.

Position wires around adjustment screw post so wires will not

interfere with cover travel.

Point A

The Foredom Electric Company 1

Summary of Contents

Page 1 - The Foredom Electric Company

QtyDescriptionPart No.Item1CoverCP10852B11Trigger Switch, 250VCP1102721BaseCP1085131Front Base PadCP1085941Screw, 6−32 x 1"CP1085651Washer, #6CP1

Related models: C.FCT-2

Comments to this Manuals

No comments

Foredom C.FCH-2 User Manual

Browse online or download User Manual for For the car Foredom C.FCH-2. Foredom C.FCH-2 User Manual

Summary of Contents

Related models: C.FCT-2

Comments to this Manuals

Related products and manuals for For the car Foredom C.FCH-2